info@redvancetech.com +86 135 3679 1558 OEM / ODM Manufacturer · Shenzhen
 
Technical / LED Masks / Battery and Driver Design

A cordless LED mask is tested on a full battery and used on whatever is left. If the driver does not hold the LED current steady as the battery drains, and the mask does not shed heat away from the skin, the output a buyer measured on day one is not the output a user gets at the end of a week. This is a system integration question, and it is testable before you order.

Moving the battery and controller into the mask removes the cable and the handheld control box. It also puts a lithium cell, a driver board and a few dozen LEDs on a curved shell against the face, with less room for heat to go anywhere and a power source whose voltage changes every minute of use.

Brands entering LED beauty from other consumer electronics categories often compete on this exact format: wireless, controller-free, lighter. The comparison that matters is not LED count. It is whether the mask delivers the same light at the end of the charge as at the start, without running warm against the skin. This guide covers why output can drift, how to test it, and what to ask an ODM. It is part of our ODM platform verification series.

Short answer

Measure irradiance at fixed points from full charge to automatic shutoff, and skin-side surface temperature across back-to-back sessions. A well-integrated mask holds its output close to flat until the driver can no longer regulate, then warns or stops the session. A poorly integrated one dims gradually, so every session delivers a different dose and nobody notices. Ask the ODM for its driver design, its discharge curve data and its low-battery behaviour in writing.

01

Why output can drift in a cordless mask

Three things change during use, and each one can change how much light reaches the skin.

What changesWhy it mattersWhat good design does
Battery voltageA typical lithium-ion cell falls from about 4.2 V when full toward roughly 3 V near empty. LED light output follows LED current.A regulated constant-current driver holds LED current steady across most of that range.
LED temperatureLED output falls as junction temperature rises, and the amount differs by LED type and wavelength.A heat path that moves heat away from the LEDs and away from the skin.
Mask positionA heavier front-loaded mask can sag or shift, changing the distance between LEDs and skin.Weight placed and balanced so the shell keeps its designed distance.

The first one is the cordless problem. If LED current is set by a resistor, or by switching the battery voltage straight to the LEDs, output tracks the battery downward. A regulated driver, often with a boost or buck-boost stage depending on how the LEDs are wired, keeps current flat until the battery can no longer supply what the circuit needs. The design question is what happens at that point. For the driver side of this, see our guide to the LED driver and controller interface.

Output rule: dose is irradiance multiplied by time. A mask that runs a fixed session timer while its output falls delivers less each session, with no change on the display. Steady output, or a clear stop, is the only honest behaviour.

02

The discharge test

This test answers one question: does the mask deliver the same light on its last session of a charge as on its first?

  1. Build a fixture. Mount the mask on a rigid head form or jig so the sensor sits at the same position and distance every time. Pick points in the forehead, cheek and chin zones.
  2. Charge fully, then let the mask rest to room temperature.
  3. Run sessions back to back in the mode the runtime claim is based on, measuring irradiance at each point at the start, middle and end of every session.
  4. Continue to automatic shutoff. Record what the mask does on the way: any warning, any change in brightness, how the session ends.
  5. Express results as a percentage of the first reading at each point. Absolute values depend on the meter; the shape of the curve is the finding.
  6. Repeat on at least three units, because one good sample tells you about one sample.

Use a meter suited to multi-wavelength LEDs, because some meters read accurately only at the wavelength they were calibrated for. Our guides to reading an irradiance test report and commissioning independent testing cover the method in more depth.

Illustrative example / hypothetical readings, not measured data

Two sample masks, same LED count, same claimed runtime. Mask A reads 100 percent at the start of the first session and 97 percent at the start of the last, then shows a low-battery warning and ends the session. Mask B reads 100 percent, then 88, then 76 across the charge, and never warns. On a spec sheet they look identical. In use, Mask B’s last sessions deliver about three quarters of the light of its first.

03

The skin-side temperature test

In a cordless mask the battery, the driver and the LEDs share a small, enclosed shell next to the face. Measure what the skin side of that shell actually reaches.

  • Place thermocouples on the inner surface at the LED zones and at the points closest to the battery and driver board.
  • Test at a stated room temperature, mounted on a head form, so warm air is trapped the way it is in use.
  • Run a full session, then back-to-back sessions, because one session from cold hides the heat a second session adds.
  • Record the hottest point and when it occurs, not the average.
  • Repeat while charging if the mask can be used while plugged in, and check that the manual says whether it can.

Which surface temperature limits apply depends on how the device is classified and where it is sold. Medical electrical equipment standards such as IEC 60601-1 set limits by contact duration; other product categories follow other standards. Ask the ODM which standard it designed to and which limit it tested against, then check that the test conditions match real use. Rising temperature also lowers LED output, so a hot mask is usually a dimmer one; our article on thermal drift and warm-up explains the effect on panels.

04

Reading a runtime claim

“Up to 10 sessions per charge” is only meaningful with its conditions. Ask for each one in writing.

QuestionWhy it matters
Which mode and session length?Runtime in the lowest mode says little about the mode users choose.
Measured to what end point?“Until shutoff” can include sessions where output had already dropped.
Output at the last counted session?A session only counts if it delivers the specified light.
At what room temperature?Battery capacity and LED efficiency both change with temperature.
On new cells or after cycling?Lithium cells lose capacity with charge cycles, so runtime on a fresh unit is the best case.

Battery capacity in mAh is an input, not a result. Two masks with the same cell can deliver very different usable sessions depending on driver efficiency, LED efficiency and how the firmware handles low charge.

05

What to ask the ODM

Supplier questions

Cordless mask integration

  1. Driver topology: is LED current regulated, and over what battery voltage range does it stay regulated?
  2. Discharge data: irradiance at fixed points from full charge to shutoff, on more than one unit.
  3. Low-battery behaviour: does the mask warn, end the session, or dim? Who decided, and is it in the firmware specification?
  4. Thermal data: skin-side surface temperature across back-to-back sessions, with test conditions and the standard it was assessed against.
  5. Weight and balance: total mass, where the battery sits, and how the designed LED-to-skin distance is held in use.
  6. Runtime basis: mode, session length, end point, temperature and cell age behind the claim.
  7. Battery safety evidence: the cell and pack certifications covered in our battery-powered device safety guide.

A supplier with its own driver and firmware design can answer every one of these from its own records. A supplier assembling a bought-in mask platform will often have to ask someone else, which is itself an answer. Optical layout, eye safety and fit are covered separately in our LED face mask engineering guide.

06

The rest of this series

07

Where RedVance stands

Our production devices are mains-powered panels, and we do not publish measured data for any mask. We will not quote mask output, runtime or temperature figures until they have been measured on the actual design.

What carries over is the discipline this article is about. We design our own boards and firmware, and the driver in our LED60 is flicker-free, with measured irradiance of 190 mW/cm² at 15 cm. If you send us a mask specification or sample, we will tell you which of the tests above it needs, and say plainly whether our electronics work is a fit for it or not.

Frequently asked questions

How do I verify a cordless LED mask keeps its output as the battery drains?

Mount the mask on a fixture, charge it fully, and measure irradiance at fixed points at the start, middle and end of back-to-back sessions until automatic shutoff. Express each reading as a percentage of the first. Repeat on at least three units.

How do I verify whether a mask uses a constant-current LED driver?

Ask the ODM to state whether LED current is regulated and over what battery voltage range, then check it with the discharge test. A regulated driver gives a flat output curve until the battery can no longer support it. Output that falls steadily with charge suggests the current is not regulated.

How do I verify what a mask does when the battery is low?

Run it to automatic shutoff during the discharge test and record what happens: a warning, an ended session, or gradual dimming. Then ask for the low-battery behaviour in the firmware specification, so it stays the same in production.

How do I verify a cordless mask does not get too warm against the skin?

Place thermocouples on the inner surface at the LED zones and near the battery and driver, mount the mask on a head form at a stated room temperature, and record the hottest point across back-to-back sessions. Ask which standard and limit the ODM tested against.

How do I verify a mask’s runtime claim?

Ask for the mode, session length, end point, room temperature and cell age behind the claim. Then check that the last counted session still delivered the specified output. A session that runs but delivers much less light should not count toward runtime.

How do I verify an ODM designed its mask electronics itself?

Ask for the driver design, discharge curve data, firmware low-battery logic and thermal test records. A supplier that designs its own electronics can answer from its own files. One assembling a bought-in platform will usually need to ask another company.

RedVance / Mask test plan

Send us your mask specification or sample. We will tell you what to test, and whether we fit.

Share the spec sheet, the supplier’s runtime claim or a sample. We will mark which tests in this guide it still needs, list the questions to put to the ODM, and tell you honestly whether our electronics work is a match for the project.

Plan my mask tests →
Sources

Touch temperature limits by contact duration in medical electrical equipment: Advanced Energy, maximum temperature per IEC safety standards

Battery safety and transport standards for cordless devices: RedVance battery-powered device safety guide

Mask optics, eye safety and fit: RedVance LED face mask engineering guide

Educational content for B2B product development. Not engineering, safety or regulatory advice. Hypothetical readings are labelled and are not measurements of any product. Applicable safety standards and temperature limits depend on the device’s classification and market. RedVance does not manufacture masks and makes no claim of mask performance. No medical claims are made.

Leave a Reply

Your email address will not be published. Required fields are marked *